Need a book? Engineering books recommendations...

Return to index: [Subject] [Thread] [Date] [Author]

Re: Wood interior wall studs

[Subject Prev][Subject Next][Thread Prev][Thread Next]
Title: Re: Wood interior wall studs
Excellent points Jordan, and I would also add to that the need to consider notching/ drilling  the studs
for the electrical outlets.


Tarek Mokhtar, SE
Laguna Beach, CA




I do a lot of wood, and here's my take:

The 5psf should be at a Cd of 1.6.  Why? Unless I have an intentionally pressurized room (which is not the case here), there is no possible way that common construction techniques can _maintain_ that kind of pressure differential over an extended period of time, and if you have a constant load (say, a commercial kitchen with doors that seal tight...right...) making the pressure differential then the HVAC engineer should already be providing makeup air in that area.  The building code can call it a "live" load all it wants, but the actual duration of load will never reach 10 years in the 50 year design life of the building.

Roof live load should be given a Cd of 1.25; snow is 1.15.

I don't recommend a loadbearing wall of 10' in height be made of 2x4s. Why? Because the walls will not be sheathed before the floor joists are set into place. The code limits the L/d ratio to 75 for construction, and a 10' 2x4 has an L/d of 80. The contractor cannot build the wall unless he plans on bracing every stud without violating the code.

And, for the record, I agree with Don that 2x4s 10 feet long look a lot like spaghetti. And as a bearing wall they give me the willies. My answer to such a request is normally to do it as designed, or provide another PE to seal off on the change with full calculations, and provide me with a full release of liability should anything happen.  I've never been taken up on the offer.
Jordan


Andy Heigley wrote:
Everyone:
 
Thanks for your responses?
 
Here are my responses to some of your questions back:
 
  • I would design for LL and LLr if the wall were supporting both the floor and roof loads.
 
  • I am designing to ASD.
 
  • I guess I'm a little leary of using the Cd of 1.6 for this reason.  The duration factor is applied to both bending and axial capacities.  Applying 60% more to the allowable axial stress makes a huge difference.  And if you have a 4 story building, for example, you are going to be approaching the capacity of the stud just due to DL and LL?  you then add a "little bit" of short term horizontal loading to the stud and increase the capacities by 60% seems non-conservative.
 
  • Scott:  I haven't found the rated wall design reduction factors you've mentioned.  Can you tell me the code section that is in?
 
  • 10'-0" high 2x4's? exactly why I initially called for 2x6 stud walls, but the GC is flipping out about it? I get the old, "I've been doing this for 30 years, and never had to do this before"?
 
 
Andrew Heigley, PE
 
 
 
 
******* ****** ******* ******** ******* ******* ******* *** * Read list FAQ at: http://www.seaint.org/list_FAQ.asp * * This email was sent to you via Structural Engineers * Association of Southern California (SEAOSC) server. To * subscribe (no fee) or UnSubscribe, please go to: * * http://www.seaint.org/sealist1.asp * * Questions to seaint-ad(--nospam--at)seaint.org. Remember, any email you * send to the list is public domain and may be re-posted * without your permission. Make sure you visit our web * site at: http://www.seaint.org ******* ****** ****** ****** ******* ****** ****** ********


--

Tarek Mokhtar, SE
TMM Structural Engineers, Inc
31645 S. Coast Hwy
Laguna Beach, CA., 92651
949-499-6254
949-499-2777 Fax