Need a book? Engineering books recommendations...

Return to index: [Subject] [Thread] [Date] [Author]

Re: WA SE III Exam

[Subject Prev][Subject Next][Thread Prev][Thread Next]
Marlou,

No you don't have to take any exams. The process is slow and you have to fill out a bunch of stuff, but no re-testing.

-gm

On Mon, Jun 23, 2008 at 1:26 AM, Marlou Rodriguez <mbrodrig(--nospam--at)mbrodriguez.com> wrote:

I too am planning on getting this.  Does anyone know if a California SE can get a Washington SE via comity.  Someone once told me that I had to take the Washington SE III exam.  Is this true.

 

Thanks.

 

From: Scott Maxwell [mailto:smaxwell(--nospam--at)umich.edu]
Sent: Sunday, June 22, 2008 11:45 PM
To: seaint(--nospam--at)seaint.org
Subject: RE: WA SE III Exam

 

I looked it up in the most recent newsletter...pass rate for last October was 22% (107 took it and only 24 passed).

 

Regards,

 

Scott

Adrian, MI

-----Original Message-----
From: Jake Watson [mailto:jake.watson1(--nospam--at)gmail.com]
Sent: Sunday, June 22, 2008 5:57 PM
To: seaint(--nospam--at)seaint.org
Subject: Re: WA SE III Exam

Thanks for confirming what I assumed.  It's amazing there isn't more information available on this exam.  It would be great to see some past exam questions.  I realize studying isn't the only way to pass the exam.  However, I am good at preparing for these exams when I have some samples to work.  I'm sure the books will start arriving when CA begins testing on the IBC.  I have some old CA SE (pre- NCEES) exam samples.  I will probably work those and translate to the IBC.

By the way, I am taking the WA exam because CA now accepts it.  CA has been a royal pain in my rear end.  I plan on getting comity if I am lucky enough to pass in WA.  Any idea on the WA pass rates?

Jake Watson, SE
Salt Lake City, UT

On Sat, Jun 21, 2008 at 10:26 PM, Scott Maxwell <smaxwell(--nospam--at)umich.edu> wrote:

This all assumes that it has NOT changed since I took it roughly 4 years ago the last time...

 

It is essay (i.e. long hand calculations with partial credit).  It is an 8 hour exam.  There are 4 problems to do...two in the morning and two in the afternoon.  In each session, if I recall correctly, there are three problems...one that you have to do and the second is a choice between a bridge and building problem...but both could be a choice between a bridge and building problem...I just don't recall for sure.  I do know that you DO NOT have to do bridge problems if you don't want (i.e. they are optional).

 

I don't know how close it is to the new CA SE III format as I have not taken the CA SE III and now that CA accepts the WA SE for reciprocity, it looks like I never will if I want my SE in CA.  I would suspect that it is rather similar.

 

I am not aware of any study guides, but there might be some.

 

It makes the Struct II exam look easy...at least compared to how the Struct II exam was when I took it.  And it makes the Struct I exam look like a complete joke (as well as the Civil PE exam).

 

My best advice, study and know all four major materials. Every time (third time was the charm...but then I am never too fond of studying and did not study much...besides, if you get to do well rounded design...i.e. all materials and wind and seismic...on a regular basis, then should be in pretty good shape without studying) I took the exam, all four materials were covered each time.  Know the wind provisions and the seismic provisions...you WILL get a problem on each at least.  Time is definitely a factor, so make sure you know where stuff is and don't have to waste too much time looking it up.  You can bring books and codes, so you can bring textbooks and such as "crutches", but if you have to use them too much, then you are likely dead.

 

Good luck.  Let me know if you have any more questions and I will see if I can answer them.

 

Regards,

 

Scott

Adrian, MI

-----Original Message-----
From: Jake Watson [mailto:jake.watson1(--nospam--at)gmail.com]
Sent: Saturday, June 21, 2008 4:53 PM
To: SEAINT
Subject: WA SE III Exam

I am looking into taking the Washington SE III Exam.  The exam program on WA's website is very generic and of little help.  I have tried looking for a study guide or other references which may shed some light on it.  So far, I have come up empty.  Can anyone shed some light on this exam?  What is the format (essay, multiple choice, a mixture)?  Are sample or past exams available?  Bridge codes are listed in the program.  Is bridge content compulsory or optional?  Are there study guides available that I simply can't find?  How close is it to the new CA SE III format?

Thanks,
Jake Watson, SE
Salt Lake City, UT